Modifications and Repairs

VEMS V3.3 Dead cpu after MCP3208-failure?

Started by kgbengt

Replies: 1
Views: 19,889

March 03, 2020, 08:12:36 AM
by gunni

Blown trigger hardware??

Started by Arthur

Replies: 6
Views: 19,526

January 06, 2010, 06:19:11 PM
by Arthur

Board v3.7 Primary Trigger converting from VR to HALL

Started by Darkweb

Replies: 0
Views: 19,364

June 11, 2020, 06:51:41 AM
by Darkweb

no serial nr

Started by izmirliss

Replies: 0
Views: 19,279

February 10, 2020, 03:00:07 PM
by izmirliss

Vems ARF - EGT Gauge, AFR always reads 21.8

Started by James Supra

Replies: 7
Views: 19,108

February 06, 2011, 04:44:49 PM
by [email protected]

VEMS failing to boot

Started by msh

Replies: 0
Views: 18,915

June 19, 2020, 07:55:01 PM
by msh

TGV (tumble generator valve) delete

Started by natedogg

Replies: 0
Views: 18,802

August 17, 2020, 07:51:40 PM
by natedogg

Spare parts

Started by paul_f

Replies: 6
Views: 18,473

August 11, 2010, 11:11:47 AM
by PeepPaadam

Problem with Firmware Upload / Validation fails

Started by Infinity

Replies: 4
Views: 18,303

May 30, 2013, 05:24:00 PM
by mattias

FET drivers

Started by vsc

Replies: 5
Views: 18,215

August 02, 2013, 08:39:56 PM
by vsc

Failed 18V TVS overvoltage protection.

Started by GintsK

Replies: 5
Views: 18,193

May 11, 2010, 10:09:12 PM
by GintsK

VEMS locked in boot loader mode.

Started by dnb

Replies: 2
Views: 18,079

December 06, 2011, 10:50:42 PM
by Ignitec

What chip?

Started by ranz

Replies: 2
Views: 17,828

August 17, 2010, 03:19:04 AM
by ranz

Fried my ECU

Started by ethergore

Replies: 5
Views: 17,727

June 11, 2015, 05:41:33 PM
by jrussell

Is there any reason to not use a different sort of IGBT for ignition channels?

Started by dnb

Replies: 4
Views: 17,676

October 16, 2009, 05:38:19 PM
by SamSpade

Speed signal from GPS instead of a wheel.

Started by gunni

Replies: 4
Views: 17,580

October 26, 2009, 11:46:09 PM
by gunni

MCP3208 input voltages erratic

Started by Sprocket

Replies: 4
Views: 17,385

October 25, 2009, 04:01:18 AM
by Sprocket

PWM controled water injection pump speed/pressure

Started by mads b (dk)

Replies: 5
Views: 17,339

August 08, 2015, 06:12:15 AM
by mads b (dk)

Removing glue

Started by paul_f

Replies: 5
Views: 17,301

August 11, 2010, 11:13:42 AM
by PeepPaadam

No trigger on EC35 Logic level

Started by Hillmanjames

Replies: 1
Views: 17,208

May 27, 2017, 07:09:14 PM
by Hillmanjames