Configuration

Wideband pump calibrations

Started by Agriv8

Replies: 9
Views: 46,216

January 12, 2013, 09:29:30 AM
by GintsK

What do you think of this tool - Config table helper

Started by 16Victor

Replies: 4
Views: 37,329

May 13, 2009, 05:43:11 PM
by 16Victor

VEMS v3.3 Wideband & EGT Configuration

Started by [email protected]

Replies: 0
Views: 33,516

April 01, 2007, 01:01:51 PM
by [email protected]

VEMS v3.3 ECU Wideband Configuration ***VEMS ECU USERS READ THIS***

Started by [email protected]

Pages1 2 3

Replies: 30
Views: 145,611

April 14, 2013, 05:08:23 PM
by Sprocket

VEMS communication methods.

Started by gunni

Replies: 1
Views: 33,536

February 11, 2009, 02:30:48 PM
by PeepPaadam

tests for knock sensor

Started by multiplex

Pages1 2 3

Replies: 41
Views: 124,728

August 09, 2011, 09:06:32 PM
by Jamo

Temperature Sensor Configuration

Started by [email protected]

Pages1 2

Replies: 19
Views: 79,022

February 23, 2009, 09:44:51 PM
by [email protected]

Priming, Cranking, Afterstart

Started by [email protected]

Pages1 2

Replies: 27
Views: 90,574

January 12, 2013, 09:36:47 AM
by GintsK

Converting to AlphaN (TPS vs RPM)

Started by [email protected]

Pages1 2 3

Replies: 37
Views: 137,935

September 05, 2013, 05:17:16 PM
by wazzu70

Base Fuel Tables

Started by antonch

Replies: 4
Views: 39,162

March 01, 2017, 08:05:43 AM
by Anden83

AlphaN with Boost compensation

Started by NOTORIOUS VR

Replies: 6
Views: 44,814

January 30, 2009, 01:33:43 AM
by mattias

Wrong Starting - Cranking/Afterstart

Started by JRD McLAREN

Replies: 3
Views: 13,941

July 17, 2012, 07:51:20 PM
by JRD McLAREN

Windows 7 not connecting via serial?

Started by badjuju

Replies: 1
Views: 13,289

April 14, 2010, 02:27:04 PM
by mel

where to start with AAN motronic VEMS?

Started by mswanson

Replies: 7
Views: 29,887

October 10, 2007, 10:29:13 PM
by mswanson

where to put the 2nd knock sensor enable on the Vems soft...????

Started by rossi46numberone

Replies: 10
Views: 22,179

March 04, 2011, 12:05:54 PM
by z0tya

where is the stepper chip?

Started by smurfinator

Replies: 1
Views: 14,287

September 13, 2008, 05:34:56 PM
by [email protected]

When Cranking , crank state remains off, RPM 0. Triggers seem to work.

Started by rico_pl

Replies: 1
Views: 13,410

August 23, 2018, 05:49:50 PM
by jrussell

What settings to use for 42lb/hr injectors

Started by max

Replies: 2
Views: 14,394

September 02, 2009, 05:48:54 PM
by max

What is RPM/MAP MAP Correction used for?

Started by wazzu70

Replies: 8
Views: 22,129

September 22, 2013, 11:18:55 PM
by fphil

what is IAC int, IAC IE, IAC PE, IAC Target RPM

Started by fphil

Replies: 3
Views: 14,481

November 14, 2013, 11:28:22 AM
by VEMS