1.0.78

[[email protected]]

That aint mine, you might want to try dropping those binaries that Gints posted and you should have the live table stuff.

[Denmark]

Rob, you could be nice to us, and compile a complete packede of the 1.0.78, with every thing needed.

There are some new things in the 1.0.78 packede, that are on the wiki side, and i will try to upload that to the Subaru when i get the time...

/Skassa

[GintsK]

http://kotisivu.dnainternet.net/sakrkorh/vems/firmware_1.0.78.zip

Is this yours Rob?
It doesn´t seem to have the live table editing bits.

It have. Be little more accurate with mouse!

[gunni]

http://kotisivu.dnainternet.net/sakrkorh/vems/firmware_1.0.78.zip

Is this yours Rob?
It doesn´t seem to have the live table editing bits.

It have. Be little more accurate with mouse!

What are the commands?
I wasn´t getting anything to work testing and live editing and multiple cells

[GintsK]

Just watch this video!
http://www.diyautotune.com/videos/megatune/megatune225p1_multicell_select.wmv
Hope this helps!

Gints

[gunni]

Got it

this is an excellent upgrade.
Now having a working lambda meter in the VE table would be nice.

[Denmark]

Have any of you tried the 1.0.78?

It seems that i need to take out lots of fuel in the ve table, and even lowering the req fuel, to get the car running, this is if i write 100 in the MAT enrichment.
I have disabled the N2O settings, and have made a new load and rpm bin, as this gets totaly wrong, when uploading this, over the 1.0.73, that was in before.

I have now put back in the old 1.0.73, to get the car running again, as it seems a bit random with the fuel needs....sometimes it needs more sometimes it needs less?


And i did not cure the start/cranking error i got,this week i will try a small adaptor board add-on, to see if it can cure the cranking problems, and make it start like its supposed to.
This is a small print that will change the signal from the cas and cam to a 4+1 signal,so i hope that the vems can run that, without problems


/Skassa

[gunni]

I haven´t yet.

What is causing different PW?

[Denmark]

I haven´t yet.

What is causing different PW?

Yes that is the question, i dont know, but the fuel requrement is not the same with 1.0.78 as it is with 1.0.73, lots of fuel needs to be removed from the ve table.

I could be nice to know the scaling that is used to the MAT enrichment, the scale in megatune goes to 155, i dont know if that means

[[email protected]]

  THIS IS A TEST RELEASE - USE AT YOUR OWN RISK

I've done a new candidate of this:
http://www.vems.co.uk/VEMSTech/VemsMT1.0.78rc2.zip

It has a new version of makeconfig.exe which copes with the extended configuration properly.

  THIS IS A TEST RELEASE - USE AT YOUR OWN RISK

[[email protected]]

Yes that is the question, i dont know, but the fuel requrement is not the same with 1.0.78 as it is with 1.0.73, lots of fuel needs to be removed from the ve table.

I could be nice to know the scaling that is used to the MAT enrichment, the scale in megatune goes to 155, i dont know if that means

All I can find is this: http://www.vems.hu/wiki/index.php?page=MembersPage%2FPhatBob%2FFieldReport

[gunni]

I haven´t yet.

What is causing different PW?

Yes that is the question, i dont know, but the fuel requrement is not the same with 1.0.78 as it is with 1.0.73, lots of fuel needs to be removed from the ve table.

I could be nice to know the scaling that is used to the MAT enrichment, the scale in megatune goes to 155, i dont know if that means

What is needed is the FULL explanation of the fuel calculations for each firmware.
then we could see the relationship and difference that are causing this strangeness

[Denmark]

Yes that is the question, i dont know, but the fuel requrement is not the same with 1.0.78 as it is with 1.0.73, lots of fuel needs to be removed from the ve table.

I could be nice to know the scaling that is used to the MAT enrichment, the scale in megatune goes to 155, i dont know if that means

All I can find is this: http://www.vems.hu/wiki/index.php?page=MembersPage%2FPhatBob%2FFieldReport

Okay,Thanks,

This gives me a idea on a start up setting.

Thanks,this will be helpfull.
/Skassa

[Sprocket]

Edit. I cant get the GUI Vems Tune GUI to work, for what ever reason. Also MT 2.25p3 looks and works like any other MT 

What am I doing wrong

[Sprocket]

Edit,Edit GUI Vems Tune GUI seems to work now for me with only a coupel of glitches that causes a crash, but, i have not yet connected to the ECU

Whats the score with the Megatune 2.25p3? It doesnt look like that, that is in the video linked above, and I cannot select and modify any more that one cell. And, there are no task buttons on the top right.