Print Page - Audi 20V Turbo 5 Cylinder

Title: Audi 20V Turbo 5 Cylinder
Post by: Regler on February 28, 2009, 02:47:29 AM

Hello,

i have follow problem with a 20V Turbo engine.

I have primary trigger 60-2

The engine is started and to 4000 rpm is all very good over 4000 rpm the engine make a limiter function the spurk is out and under 4000 rpm is the spark on an so on and so on.

The config is good, I have the same config with audi trigger 135 VR crank home and the engine runing perfect over 8000 rpm

I take the same config and change follow set up
Primary trigger, Secondary trigger and reference table h1

Have you a Idea????

Sorry for my bad english ::)

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: GintsK on February 28, 2009, 03:25:24 AM

What 60-2 you use?

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on February 28, 2009, 03:33:36 AM

As Gints says, lets be sure that your trigger is okay - one problem that often comes to the fore is that there is a limiter in Launch control that seems to effect running.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on February 28, 2009, 02:52:30 PM

Hello,

The audi 20V Turob engine have original 135 teeth flywheel (trigger1) and 1 setpoint 62Â° before TDC and 1 Campuls triger (complette 3 trigger)

I would like a other flywheel with a 5,5" Tilton clutch and then I can not take this 2 trigger, i take a 60-2 toothwheel with Hallsensor.

The Setting from this flywheel is at TDC, 11 teeth behind the missing tooth

I have follow h1 reference table setting but I m not sure is this right

0, 96, 72, 48, 24 ( what value are this?? tooth from the 60-2 or what i have no plan in moment from this reference numbers) ???

The launch control anti lag and all other extra settings are disabled

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on February 28, 2009, 04:42:12 PM

Sorry - do you say that you have a 60-2 trigger or want to fit one?

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on February 28, 2009, 05:52:10 PM

Hello rob,

sorry for my bad english

The engine is ready 60-2 trigger and all other parts are install.

The engine is runnig to 4000 rpm without problems over 4000 rpm i have this problem.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Hanky on February 28, 2009, 07:33:13 PM

Quote from: Regler on February 28, 2009, 02:52:30 PM
i take a 60-2 toothwheel with Hallsensor.

What kind of a sensor are you using?
You often use a VR sensor when running 60-2.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on February 28, 2009, 07:39:47 PM

Hello,

the sensor is a Hallsensor not VR.

I have prove the sensor with other distance there is no go.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Hanky on February 28, 2009, 07:54:09 PM

Do you have more info on the sensor? brandname and modell?

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 01, 2009, 12:52:20 AM

Hello,

the sensor and the multitoothwheel is original VW part. The distance is fix.

I mean thats my setting is not OK, but i have many settings prove the engine is running without problems, starting all functions are OK.

At 4000 rpm and higher then spark cut, all antilag or launchcontrol settings are disaabled

the h1 table what value are this tooth or degree??

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: GintsK on March 01, 2009, 11:07:50 PM

Just post .msq and note firmware version.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 02, 2009, 01:28:09 AM

Hello

here is the msc file in word form

The Firmware version is 1.1.41
I must more post the complette file is to long for one post

<?xml version="1.0" encoding="ISO-8859-1"?>
<msq xmlns="http://www.msefi.com/:msq">
<bibliography author="MegaTune 2.25 p3" writeDate="2009-03-01T19:53:33+01:00" />
<versionInfo fileFormat="4.0" nPages="9" signature="VEMS v1.1.41 16x14 kpa=2,2" />
<page number="0" size="24">
<constant name="h0" rows="8" units="inj">
1
2
4
8
16
32
64
128
</constant>
<constant name="h00">1</constant>
<constant name="h01">2</constant>
<constant name="h02">4</constant>
<constant name="h03">8</constant>
<constant name="h04">16</constant>
<constant name="h05">32</constant>
<constant name="h06">64</constant>
<constant name="h07">128</constant>
<constant name="h1" rows="8" units="inj">
0
96
72
48
24
0
0
0
</constant>
<constant name="h10">0</constant>
<constant name="h11">96</constant>
<constant name="h12">72</constant>
<constant name="h13">48</constant>
<constant name="h14">24</constant>
<constant name="h15">0</constant>
<constant name="h16">0</constant>
<constant name="h17">0</constant>
<constant name="h2" rows="8" units="inj">
104
64
56
72
88
32
32
32
</constant>
<constant name="h20">"(STEPPER D EC18 pin 11)"</constant>
<constant name="h20_dummy">"Ign"</constant>
<constant name="h20_dummy7">"0"</constant>
<constant name="h21">"4 (EC36 Pin 11)"</constant>
<constant name="h21_dummy">"Ign"</constant>
<constant name="h21_dummy7">"0"</constant>
<constant name="h22">"(STEPPER A EC18 pin 4)"</constant>
<constant name="h22_dummy">"Ign"</constant>
<constant name="h22_dummy7">"0"</constant>
<constant name="h23">"(STEPPER B EC18 pin 10)"</constant>
<constant name="h23_dummy">"Ign"</constant>
<constant name="h23_dummy7">"0"</constant>
<constant name="h24">"(STEPPER C EC18 pin 5)"</constant>
<constant name="h24_dummy">"Ign"</constant>
<constant name="h24_dummy7">"0"</constant>
<constant name="h25">"2 (EC36 Pin 34)"</constant>
<constant name="h25_dummy">"Ign"</constant>
<constant name="h25_dummy7">"0"</constant>
<constant name="h26">"2 (EC36 Pin 34)"</constant>
<constant name="h26_dummy">"Ign"</constant>
<constant name="h26_dummy7">"0"</constant>
<constant name="h27">"2 (EC36 Pin 34)"</constant>
<constant name="h27_dummy">"Ign"</constant>
<constant name="h27_dummy7">"0"</constant>
<constant name="h2d0">"(STEP C,D EC18 pin 5,11)"</constant>
<constant name="h2d1">"3+4 (EC36 Pin 36+11)"</constant>
<constant name="h2d2">"INVALID"</constant>
<constant name="h2d3">"(STEP A,B EC18 pin 4,10)"</constant>
<constant name="h2d4">"(STEP B,C EC18 pin 10,5)"</constant>
<constant name="h2d5">"1+2 (EC36 Pin 33+34)"</constant>
<constant name="h2d6">"1+2 (EC36 Pin 33+34)"</constant>
<constant name="h2d7">"1+2 (EC36 Pin 33+34)"</constant>
</page>
<page number="1" size="254">
<constant name="mapBins" rows="14" units="kPa">
30
46
56
60
70
80
96
110
136
180
230
290
350
400
</constant>
<constant name="rpmBins" rows="16" units="RPM">
700
1100
1400
1700
2200
2600
3000
3500
4000
4600
5100
5500
6000
6400
6900
7400
</constant>
<constant cols="16" name="veTable" rows="14" units="%">
86 89 91 94 95 96 97 98 99 99 99 99 99 99 98 99
88 91 94 96 97 97 97 99 100 100 100 100 100 99 99 99
90 92 94 96 98 98 98 99 100 99 99 98 99 99 99 99
92 94 97 99 100 100 100 101 102 102 102 101 99 99 99 99
92 95 98 100 101 101 102 102 103 103 102 102 100 100 100 100
94 96 99 100 102 102 103 104 104 104 105 105 105 106 108 108
96 100 99 101 103 103 105 106 107 108 109 109 110 111 113 115
99 102 103 104 105 106 107 108 109 110 112 114 116 118 122 126
102 104 106 107 108 109 110 111 111 113 114 116 119 122 128 134
108 110 110 111 110 111 112 112 114 117 119 121 123 131 139 150
112 114 114 114 115 114 115 117 118 121 124 127 134 144 157 170
117 117 117 117 117 118 118 119 120 124 127 130 139 152 171 176
121 121 121 121 122 124 126 126 126 128 130 134 142 157 171 180
126 126 127 127 130 131 132 134 134 136 139 140 145 156 169 177
</constant>
</page>
<page number="2" size="254">
<constant cols="16" name="lambdaTable" rows="14" units="Lambda">
1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00
1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00
1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00
1.00 1.00 1.00 1.00 1.00 1.00 0.95 0.95 0.95 0.95 0.95 1.00 1.00 1.00 1.00 1.00
1.00 1.00 1.01 1.00 1.00 1.00 0.95 0.95 0.96 0.95 0.90 0.90 0.90 0.99 0.99 0.99
1.00 1.00 1.01 1.00 1.00 1.02 1.01 1.01 1.01 0.99 0.98 0.98 0.98 0.98 0.98 0.98
0.99 0.99 0.99 1.00 1.00 1.00 1.00 1.00 1.00 0.99 0.98 0.98 0.98 0.98 0.98 0.98
0.98 0.98 0.99 1.00 1.01 1.00 1.00 1.00 1.00 0.98 0.98 0.96 0.96 0.96 0.96 0.96
0.96 0.96 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.96 0.96 0.94 0.94 0.93 0.90
0.93 0.93 0.94 0.96 0.96 0.96 0.96 0.96 0.94 0.93 0.92 0.92 0.92 0.90 0.88 0.88
0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.88 0.86 0.85 0.85 0.85 0.85
0.83 0.83 0.83 0.83 0.83 0.83 0.83 0.83 0.83 0.83 0.83 0.83 0.79 0.79 0.79 0.79
0.77 0.77 0.77 0.77 0.77 0.77 0.77 0.77 0.77 0.77 0.76 0.76 0.76 0.76 0.76 0.76
0.77 0.77 0.77 0.77 0.77 0.76 0.76 0.76 0.76 0.76 0.76 0.76 0.75 0.75 0.75 0.75
</constant>
<constant name="mapBins1" rows="14" units="kPa">
30
46
56
60
70
80
96
110
136
180
230
290
350
400
</constant>
<constant name="rpmBins1" rows="16" units="RPM">
700
1100
1400
1700
2200
2600
3000
3500
4000
4600
5100
5500
6000
6400
6900
7400
</constant>
</page>
<page number="3" size="254">
<constant cols="16" name="advanceTable" rows="14" units="Deg">
10.00 14.75 19.00 22.50 25.00 27.75 29.25 30.50 33.50 34.75 35.25 39.00 39.00 39.50 39.00 39.00
12.00 15.25 19.00 22.50 25.00 27.75 29.25 30.25 31.75 32.75 33.50 34.25 35.00 35.50 36.25 37.00
16.75 15.50 19.00 22.50 25.00 27.00 28.50 29.75 30.00 30.75 31.50 32.25 33.00 33.75 34.50 35.25
16.50 15.25 18.50 22.25 25.00 26.75 28.00 29.00 29.75 30.25 31.00 31.50 32.00 32.75 33.50 34.25
16.00 14.50 18.00 21.50 24.25 25.75 27.25 28.00 28.75 29.00 29.50 29.75 29.75 30.25 30.75 31.25
17.00 14.50 18.00 21.25 22.00 24.75 26.75 27.75 27.25 27.00 27.00 28.00 28.00 28.00 27.00 27.00
16.00 16.00 18.50 20.25 21.25 24.50 26.75 27.50 26.75 26.25 26.00 28.00 28.50 28.75 28.75 27.00
12.25 16.00 18.50 20.25 21.00 24.25 25.75 25.25 24.75 24.75 24.75 26.75 27.75 28.00 28.25 28.00
12.00 13.75 14.75 15.50 16.25 21.00 22.75 21.75 21.00 23.75 23.75 25.25 25.25 27.50 27.50 27.00
11.50 13.00 14.00 14.75 16.00 19.50 21.25 21.00 17.50 17.50 19.25 25.75 24.75 25.00 25.75 25.00
11.25 12.50 13.50 14.25 16.00 17.75 19.00 19.75 17.75 17.00 20.75 22.25 22.00 24.25 24.75 24.25
10.75 11.75 12.75 13.75 15.25 16.50 17.25 18.00 16.25 16.50 20.50 22.25 23.50 24.50 24.00 24.00
9.00 9.50 10.75 11.75 13.50 14.50 15.25 15.25 16.25 16.25 20.25 24.25 24.50 23.50 22.50 23.50
8.00 8.25 9.00 10.25 12.00 13.00 13.75 14.00 18.25 16.00 22.00 22.00 22.50 20.75 20.75 20.00
</constant>
<constant name="mapBinsS" rows="14" units="kPa">
30
46
56
60
70
80
96
110
136
180
230
290
350
400
</constant>
<constant name="rpmBinsS" rows="16" units="RPM">
700
1100
1400
1700
2200
2600
3000
3500
4000
4600
5100
5500
6000
6400
6900
7400
</constant>
</page>

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 02, 2009, 01:32:48 AM

<page number="4" size="255">
<constant name="acmult" units="%">110</constant>
<constant name="act_rpm_channel">255</constant>
<constant name="act_rpm_channel_bits">"i7"</constant>
<constant name="act_rpm_channel_enable">"Disabled"</constant>
<constant name="act_rpm_channel_names">"Disabled"</constant>
<constant name="act_rpm_rpm" units="rpm">25500</constant>
<constant name="act_wot_channel">255</constant>
<constant name="act_wot_channel_bits">"i7"</constant>
<constant name="act_wot_channel_enable">"Disabled"</constant>
<constant name="act_wot_channel_names">"Disabled"</constant>
<constant name="act_wot_rpm" units="rpm">25500</constant>
<constant name="airden_ignore">97</constant>
<constant name="als_cut_maxtps" units="%">100</constant>
<constant name="als_cut_mintps" units="%">100</constant>
<constant name="als_deact_egt" units="Â°C">0</constant>
<constant name="als_deact_time" units="sec">0.0</constant>
<constant name="als_enrich" units="%">0.0</constant>
<constant name="als_igncut_rpm1" units="rpm">25500</constant>
<constant name="als_igncut_rpm2" units="rpm">25500</constant>
<constant name="als_input">"DISABLED"</constant>
<constant name="als_launch_input">204</constant>
<constant name="als_max_cut">"Disabled"</constant>
<constant name="als_react_tps" units="%">100</constant>
<constant name="als_retard" units="deg">102.00</constant>
<constant name="als_retard_maxtps" units="%">100</constant>
<constant name="als_retard_mintps" units="%">100</constant>
<constant name="als_retard_rpm1" units="rpm">25500</constant>
<constant name="als_retard_rpm2" units="rpm">25500</constant>
<constant name="als_rev_limit" units="rpm">25500</constant>
<constant name="als_tks_bits">"i7"</constant>
<constant name="als_tks_enable">"Disabled"</constant>
<constant name="als_tks_names">"Disabled"</constant>
<constant name="als_tks_output">255</constant>
<constant name="alternate">4</constant>
<constant name="alternateCrank">"Alternate"</constant>
<constant name="alternateCyl">"4..0"</constant>
<constant name="another_trigger_tooth">24</constant>
<constant name="aseCount">198</constant>
<constant name="asePct" units="%">75</constant>
<constant name="awev_temp_scaling" units="%">50.2</constant>
<constant name="baroCorr">"Off"</constant>
<constant name="batt_cal">198</constant>
<constant name="battfac" units="us">544</constant>
<constant name="boost_adj_channel">"7"</constant>
<constant name="boost_alternate">"Enabled"</constant>
<constant name="boost_channel">119</constant>
<constant name="boost_channel_bits">"7"</constant>
<constant name="boost_channel_enable">"Enabled"</constant>
<constant name="boost_channel_names">"P259"</constant>
<constant name="boost_conf">66</constant>
<constant name="boost_conf_pwm">"32mS"</constant>
<constant name="boost_conf_refpos">"1/5"</constant>
<constant name="boost_conf_target">"boost-target"</constant>
<constant name="boost_egtdec" units="Â°C">1000</constant>
<constant name="boost_matdec" units="Â°C">100</constant>
<constant name="boost_minpressure" units="kPa">100</constant>
<constant name="boost_openloop">"Closed loop"</constant>
<constant name="boost_pid_ilimit">125</constant>
<constant name="boost_pid_kd">71</constant>
<constant name="boost_pid_ki">50</constant>
<constant name="boost_pid_kp">150</constant>
<constant name="boost_targetoffs">230</constant>
<constant name="cam_sync_f_edge_phase">0</constant>
<constant name="cam_sync_r_edge_phase">0</constant>
<constant name="cltType">"GM"</constant>
<constant name="config11">65</constant>
<constant name="config12">64</constant>
<constant name="config13">2</constant>
<constant name="confswitch">0</constant>
<constant name="confswitch_bits">"0"</constant>
<constant name="confswitch_enable">"Disabled"</constant>
<constant name="crankCold" units="ms">15.0</constant>
<constant name="crankHot" units="ms">3.0</constant>
<constant name="crank_minper" units="usec">2736</constant>
<constant name="cranking_thres" units="rpm">300</constant>
<constant name="dbaro" units="kPa">10</constant>
<constant name="divider">"1"</constant>
<constant name="dividerbyte">1</constant>
<constant name="egoType">"Wide band"</constant>
<constant name="ego_conf">6</constant>
<constant name="ego_conf_nbo2">"Disabled"</constant>
<constant name="ego_conf_pid">"Disabled"</constant>
<constant name="ego_coolant" units="Â°C">60</constant>
<constant name="ego_delta" units="%">1</constant>
<constant name="ego_lag">4</constant>
<constant name="ego_lean_limit" units="%">12</constant>
<constant name="ego_maxmap" units="kPa">210</constant>
<constant name="ego_maxrpm" units="rpm">8500</constant>
<constant name="ego_maxtps" units="%">60</constant>
<constant name="ego_minrpm" units="rpm">7700</constant>
<constant name="ego_pid_kp">30</constant>
<constant name="ego_pid_window">1</constant>
<constant name="ego_rich_limit" units="%">4</constant>
<constant name="ego_target" units="V">0.49</constant>
<constant name="ego_warmup" units="sec">20</constant>
<constant name="egt1_cal">74</constant>
<constant name="engineType">"Even fire"</constant>
<constant name="engine_off_delay" units="s">1.0</constant>
<constant name="fan_channel">255</constant>
<constant name="fan_channel_bits">"i7"</constant>
<constant name="fan_channel_enable">"Disabled"</constant>
<constant name="fan_channel_names">"Disabled"</constant>
<constant name="fan_hyst" units="Â°C">6</constant>
<constant name="fan_temp" units="Â°C">90</constant>
<constant name="fuelcut_max_kpa" units="kPa">450</constant>
<constant name="fuelcut_min_kpa" units="kPa">16</constant>
<constant name="fuelpump_channel">80</constant>
<constant name="fuelpump_channel_bits">"5"</constant>
<constant name="fuelpump_channel_enable">"Enabled"</constant>
<constant name="fuelpump_channel_names">"INJFET"</constant>
<constant name="hybrid_rpm_a" units="rpm">0</constant>
<constant name="hybrid_rpm_m" units="rpm">0</constant>
<constant name="iac2load">0</constant>
<constant name="iac_advance">"Enabled"</constant>
<constant name="iac_afterstart_duration" units="s">1.0</constant>
<constant name="iac_afterstart_rpm" units="rpm">100</constant>
<constant name="iac_cold_idle_temp" units="Â°C">15</constant>
<constant name="iac_cold_rpm" units="rpm">1200</constant>
<constant name="iac_cold_start_pct" units="%">40</constant>
<constant name="iac_cold_start_pos">102</constant>
<constant name="iac_conf">152</constant>
<constant name="iac_deadband" units="rpm">50</constant>
<constant name="iac_dualsol">"Disabled"</constant>
<constant name="iac_ign_advance_limit" units="deg">8.00</constant>
<constant name="iac_ign_retard_limit" units="deg">6.00</constant>
<constant name="iac_ign_slope" units="deg/256rpm">5.00</constant>
<constant name="iac_ign_threshold" units="deg">6.00</constant>
<constant name="iac_integral_deadband" units="rpm">20</constant>
<constant name="iac_integral_limit_dec">35</constant>
<constant name="iac_integral_limit_inc">120</constant>
<constant name="iac_kd">10</constant>
<constant name="iac_ki">25</constant>
<constant name="iac_kp">17</constant>
<constant name="iac_max_steps">30</constant>
<constant name="iac_pid_conf_asym">"Disabled"</constant>
<constant name="iac_power_off_stepper">"Disabled"</constant>
<constant name="iac_ref_pos0">191</constant>
<constant name="iac_ref_pos1">186</constant>
<constant name="iac_ref_pos2">173</constant>
<constant name="iac_ref_pos3">168</constant>
<constant name="iac_ref_pos4">161</constant>
<constant name="iac_ref_pos5">145</constant>
<constant name="iac_ref_pos6">130</constant>
<constant name="iac_ref_pos7">122</constant>
<constant name="iac_ref_pos8">117</constant>
<constant name="iac_ref_pos9">26</constant>

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 02, 2009, 01:33:35 AM

<constant name="iac_ref_pospct0" units="%">75</constant>
<constant name="iac_ref_pospct1" units="%">73</constant>
<constant name="iac_ref_pospct2" units="%">68</constant>
<constant name="iac_ref_pospct3" units="%">66</constant>
<constant name="iac_ref_pospct4" units="%">63</constant>
<constant name="iac_ref_pospct5" units="%">57</constant>
<constant name="iac_ref_pospct6" units="%">51</constant>
<constant name="iac_ref_pospct7" units="%">48</constant>
<constant name="iac_ref_pospct8" units="%">46</constant>
<constant name="iac_ref_pospct9" units="%">10</constant>
<constant name="iac_sol_channel">96</constant>
<constant name="iac_sol_channel_bits">"6"</constant>
<constant name="iac_sol_channel_enable">"Enabled"</constant>
<constant name="iac_sol_channel_names">"INJFET"</constant>
<constant name="iac_sol_dualchannel">"7"</constant>
<constant name="iac_speed">1</constant>
<constant name="iac_step_seq">216</constant>
<constant name="iac_stepper">"PWM"</constant>
<constant name="iac_tps_thres" units="%">0</constant>
<constant name="iac_tpsfollow">"Disabled"</constant>
<constant name="iac_type">"PWM/Stepper"</constant>
<constant name="iac_warm_idle_temp" units="Â°C">60</constant>
<constant name="iac_warm_rpm" units="rpm">950</constant>
<constant name="iac_warm_start_pct" units="%">25</constant>
<constant name="iac_warm_start_pos">64</constant>
<constant name="iacref_matslope">"Disabled"</constant>
<constant name="ign_crank_advance" units="deg">10.00</constant>
<constant name="ign_dwell14" units="ms">3.07</constant>
<constant name="ign_dwellmap">0</constant>
<constant name="ign_out">112</constant>
<constant name="ign_out_dual">"Disabled"</constant>
<constant name="ign_out_inv">"Disabled"</constant>
<constant name="ign_out_type">"DUMMY"</constant>
<constant name="ign_tdcdelay" units="deg">65.0</constant>
<constant name="ignchmax">"04..00"</constant>
<constant name="ignchmaxscalar">4</constant>
<constant name="injType">"Port"</constant>
<constant name="inj_stage2_rate">255</constant>
<constant name="inj_stage2_start_map" units="kPa">510</constant>
<constant name="inj_stage2_start_tps" units="%">100</constant>
<constant name="injocfuel" units="us">192</constant>
<constant name="injopen" units="us">0</constant>
<constant name="injpwm" units="%">100.0</constant>
<constant name="injpwmt" units="ms">25.5</constant>
<constant name="injrampup_battfac" units="us">4080</constant>
<constant name="knock1_frequency">"6.94"</constant>
<constant name="knock1_gain">"1"</constant>
<constant name="knock1_integrator">"240"</constant>
<constant name="knock2_frequency">"6.94"</constant>
<constant name="knock2_gain">"2"</constant>
<constant name="knock2_integrator">"40"</constant>
<constant name="knock_advance_delay" units="ms">1200</constant>
<constant name="knock_advance_step" units="deg">0.25</constant>
<constant name="knock_chan">0</constant>
<constant name="knock_default_retard" units="deg">1.00</constant>
<constant name="knock_max_retard" units="deg">6.00</constant>
<constant name="knock_maxrpm" units="rpm">6600</constant>
<constant name="knock_mean_threshold" units="%">31</constant>
<constant name="knock_minrpm" units="rpm">1000</constant>
<constant name="knock_noise_scale">216</constant>
<constant name="knock_retard_delay" units="ms">720</constant>
<constant name="knock_retard_step" units="deg">1.00</constant>
<constant name="knock_sampling_window">242</constant>
<constant name="knock_threshold">10</constant>
<constant name="knock_window_length">"60"</constant>
<constant name="knock_window_start">"8"</constant>
<constant name="kpa_config_resolution">"2 (High-Boost)"</constant>
<constant name="kpafac" units="kPa">416</constant>
<constant name="kpafac_unit">"2 (Default)"</constant>
<constant name="kpaoffs" units="kPa">5.00</constant>
<constant name="launch_enrich" units="%">0.0</constant>
<constant name="launch_input">"DISABLED"</constant>
<constant name="launch_retard" units="deg">0.00</constant>
<constant name="launch_rpm" units="rpm">25500</constant>
<constant name="lcd_backlight" units="%">100</constant>
<constant name="lcd_c0">255</constant>
<constant name="lcd_c0_aim">"Enabled"</constant>
<constant name="lcd_c0_busypoll">"Enabled"</constant>
<constant name="lcd_c0_easygoto">"Enabled"</constant>
<constant name="lcd_c0_enabled">"Enabled"</constant>
<constant name="lcd_c0_pwm_brightness">"Enabled"</constant>
<constant name="lcd_c0_reinit">"Enabled"</constant>
<constant name="lcd_c0_sw_brightness">"Enabled"</constant>
<constant name="lcd_default_view">0</constant>
<constant name="lcd_delay">66</constant>
<constant name="lcd_delay_before">"4"</constant>
<constant name="lcd_delay_en">"2"</constant>
<constant name="loadmult">"Enabled"</constant>
<constant name="mapProportion">"TPSdot"</constant>
<constant name="mapType">"250 kPa"</constant>
<constant name="matType">"GM"</constant>
<constant name="matretard">"Enabled"</constant>
<constant name="misc1out_channel">239</constant>
<constant name="misc1out_channel_bits">"i6"</constant>
<constant name="misc1out_channel_enable">"Disabled"</constant>
<constant name="misc1out_channel_names">"Disabled"</constant>
<constant name="misc1out_maxmap" units="kPa">510</constant>
<constant name="misc1out_maxrpm" units="rpm">25500</constant>
<constant name="misc1out_maxtps" units="%">100</constant>
<constant name="misc1out_minmap" units="kPa">20</constant>
<constant name="misc1out_minrpm" units="rpm">0</constant>
<constant name="misc1out_mintps" units="%">0</constant>
<constant name="misc2out_channel">255</constant>
<constant name="misc2out_channel_bits">"i7"</constant>
<constant name="misc2out_channel_enable">"Disabled"</constant>
<constant name="misc2out_channel_names">"Disabled"</constant>
<constant name="misc2out_maxmap" units="kPa">510</constant>
<constant name="misc2out_maxrpm" units="rpm">25500</constant>
<constant name="misc2out_maxtps" units="%">100</constant>
<constant name="misc2out_minmap" units="kPa">510</constant>
<constant name="misc2out_minrpm" units="rpm">25500</constant>
<constant name="misc2out_mintps" units="%">100</constant>
<constant name="nCylinders">"5"</constant>
<constant name="nInjectors">"5"</constant>
<constant name="overrun_fuelcut" units="rpm">1600</constant>
<constant name="overrun_fuelresume" units="rpm">1500</constant>
<constant name="primary_trig0">"Rising"</constant>
<constant name="primary_trig1">"Multitooth"</constant>
<constant name="primary_trig2">"Disabled"</constant>
<constant name="primary_trig3">"Disabled"</constant>
<constant name="primary_trig4">"Disabled"</constant>
<constant name="primary_trig5">"Disabled"</constant>
<constant name="primary_trig6">"Disabled"</constant>
<constant name="primary_trig7">"Disabled"</constant>
<constant name="primary_trig_miss">"N-2"</constant>
<constant name="primary_trigger">1</constant>
<constant name="primary_trigger_sel">"Normal"</constant>
<constant name="primePulse" units="ms">0.0</constant>
<constant name="primep_temp_scaling" units="%">16.1</constant>
<constant name="pump_on_mintime" units="s">2.9</constant>
<constant name="req_fuel" units="ms">3.5</constant>
<constant name="reset_engphase_after">255</constant>
<constant name="rev_limit" units="rpm">7900</constant>
<constant name="rpmk">2400</constant>
<constant name="secondary_trig0">"Falling"</constant>
<constant name="secondary_trig1">"Enabled"</constant>
<constant name="secondary_trig2">"Disabled"</constant>
<constant name="secondary_trig3">"Coil-type"</constant>
<constant name="secondary_trig4">"Cam sync"</constant>
<constant name="secondary_trig5">"Single"</constant>
<constant name="secondary_trig7">"Disabled"</constant>
<constant name="secondary_trigger">24</constant>
<constant name="shiftcut_conf_fuel">"Disabled"</constant>
<constant name="shiftcut_conf_input">136</constant>
<constant name="shiftcut_conf_spark">"Disabled"</constant>
<constant name="shiftcut_conf_spark_rev">"Disabled"</constant>
<constant name="shiftcut_igncut">"6.25"</constant>
<constant name="shiftcut_input">"Disabled"</constant>
<constant name="shiftcut_minrpm">0</constant>
<constant name="shiftcut_pothi">0</constant>
<constant name="shiftcut_potlow">0</constant>
<constant name="shiftcut_retard">"0"</constant>
<constant name="shiftcut_retcut">0</constant>
<constant name="shiftcut_time" units="mS">508</constant>
<constant name="shiftcut_tpsthresh" units="%">0</constant>
<constant name="softrpm_idle_enable">"Enabled"</constant>
<constant name="softrpm_idle_tps" units="%">0</constant>
<constant name="softrpm_range" units="rpm">200</constant>
<constant name="softrpm_rpm" units="rpm">7900</constant>
<constant name="tach_channel">7</constant>
<constant name="tach_channel_bits">"0"</constant>
<constant name="tach_channel_enable">"Enabled"</constant>
<constant name="tach_channel_names">"P259"</constant>
<constant name="tach_divider">16</constant>
<constant name="taeBins" rows="4" units="ms">
0.4
0.6
1.2
1.3
</constant>
<constant name="taeColdA" units="ms">1.2</constant>
<constant name="taeColdM" units="%">110</constant>
<constant name="taeRates" rows="4" units="ms">
0.8
1.4
2.9
5.1
</constant>
<constant name="taeTime" units="ms">0.3</constant>
<constant name="tooth_wheel">58</constant>
<constant name="tooth_wheel_twidth1">6</constant>
<constant name="tooth_wheel_twidth2">18</constant>
<constant name="toothrel_missing">214</constant>
<constant name="toothrel_missing_lower">"200"</constant>
<constant name="toothrel_missing_upper">"413"</constant>
<constant name="toothrel_normal">132</constant>
<constant name="toothrel_normal_lower">"25"</constant>
<constant name="toothrel_normal_upper">"150"</constant>
<constant name="tps_high" units="ADC">249</constant>
<constant name="tps_low" units="ADC">20</constant>
<constant name="tpsacold" units="mS">1.2</constant>
<constant name="tpsaq" rows="4" units="mS">
0.4
0.6
1.2
1.3

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 02, 2009, 01:34:23 AM

</constant>
<constant name="tpsaq1" units="mS">0.4</constant>
<constant name="tpsaq2" units="mS">0.6</constant>
<constant name="tpsaq3" units="mS">1.2</constant>
<constant name="tpsaq4" units="mS">1.3</constant>
<constant name="tpsasync" units="s">0.3</constant>
<constant name="tpsdot_kpadot_conf">"Throttle based"</constant>
<constant name="tpsdotrate" rows="4" units="dv/dt">
4
7
15
26
</constant>
<constant name="tpsdt1" units="dv/dt">4</constant>
<constant name="tpsdt2" units="dv/dt">7</constant>
<constant name="tpsdt3" units="dv/dt">15</constant>
<constant name="tpsdt4" units="dv/dt">26</constant>
<constant name="trigger_tooth">0</constant>
<constant name="twoStroke">"Four-stroke"</constant>
<constant name="ve_learn_2x2">"Disabled"</constant>
<constant name="ve_learn_conf">0</constant>
<constant name="ve_learn_coolant" units="Â°C">75</constant>
<constant name="ve_learn_ego_scale">80</constant>
<constant name="ve_learn_kpa_scale">40</constant>
<constant name="ve_learn_limit" units="%">50</constant>
<constant name="ve_learn_max_power">100</constant>
<constant name="ve_learn_min_weight">20</constant>
<constant name="ve_learn_on">"Disabled"</constant>
<constant name="ve_learn_rpm_scale">40</constant>
<constant name="ve_learn_sim">"Disabled"</constant>
<constant name="ve_learn_speed">50</constant>
<constant name="warmup_clt" rows="10" units="%">
150
150
140
120
112
107
98
96
90
90
</constant>
<constant name="warmup_clt0" units="%">150</constant>
<constant name="warmup_clt1" units="%">150</constant>
<constant name="warmup_clt2" units="%">140</constant>
<constant name="warmup_clt3" units="%">120</constant>
<constant name="warmup_clt4" units="%">112</constant>
<constant name="warmup_clt5" units="%">107</constant>
<constant name="warmup_clt6" units="%">98</constant>
<constant name="warmup_clt7" units="%">96</constant>
<constant name="warmup_clt8" units="%">90</constant>
<constant name="warmup_clt9" units="%">90</constant>
<constant name="warmup_rpm_scale" units="%">66</constant>
<constant name="water_pump_channel">255</constant>
<constant name="water_pump_channel_bits">"i7"</constant>
<constant name="water_pump_channel_enable">"Disabled"</constant>
<constant name="water_pump_channel_names">"Disabled"</constant>
<constant name="water_pump_hyst" units="Â°C">70</constant>
<constant name="water_pump_temp" units="Â°C">-40</constant>
<constant name="wbo2_abs_limit">224</constant>
<constant name="wbo2_calibration">169</constant>
<constant name="wbo2_fallback" units="V">112</constant>
<constant name="wbo2_heater_pid_ilimit">128</constant>
<constant name="wbo2_heater_pid_kd">26</constant>
<constant name="wbo2_heater_pid_ki">17</constant>
<constant name="wbo2_heater_pid_kp">69</constant>
<constant name="wbo2_limit_maxt" units="s">62.9</constant>
<constant name="wbo2_nernstdc_target">135</constant>
<constant name="wbo2_pump_pid_ilimit">255</constant>
<constant name="wbo2_pump_pid_kd">0</constant>
<constant name="wbo2_pump_pid_ki">78</constant>
<constant name="wbo2_pump_pid_kp">21</constant>
<constant name="wbo2_pump_pw_zero" units="5V/256">99</constant>
<constant name="wbo2_retry_t" units="s">24</constant>
<constant name="wbo2_ri_confidence_scale">128</constant>
<constant name="wbo2_ri_target">165</constant>
<constant name="wbo2_warmup_ramp" units="mV/s">808.4</constant>
<constant name="wueBins" rows="10" units="%">
150
150
140
120
112
107
98
96
90
90
</constant>
</page>
<page number="5" size="24">
<constant name="boostTable" rows="16" units="kPa">
118
118
210
248
274
280
280
280
282
282
280
282
282
280
272
242
</constant>
<constant name="boosttps1" units="%">10</constant>
<constant name="boosttps2" units="%">30</constant>
<constant name="boosttps3" units="%">40</constant>
<constant name="boosttps4" units="%">50</constant>
<constant name="boosttps5" units="%">100</constant>
<constant name="boosttps6" units="%">100</constant>
<constant name="boosttps7" units="%">100</constant>
<constant name="boosttps8" units="%">100</constant>
<constant name="boosttpsTable" rows="8" units="TPS Scaling">
26
77
102
128
255
255
255
255
</constant>
</page>
<page number="6" size="80">
<constant name="matCorrCurve" rows="8" units="Fuel correction %">
100.00
100.00
100.00
100.00
100.00
100.00
100.00
100.00
</constant>
<constant cols="8" name="matCorrTable" rows="8" units="Fuel correction %">
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 105.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
100.00 100.00 100.00 100.00 100.00 100.00 100.00 100.00
</constant>
<constant name="matTempBins" rows="8" units="MAT Â°C">
-3
-23
0
20
40
60
80
100
</constant>
<constant name="matTempCurve" rows="8" units="MAT Â°C">
-3
-23
0
20
40
60
80
100
</constant>
<constant name="matTpsBins" rows="8" units="TPS %">
10
20
30
50
70
80
90
100
</constant>
</page>
<page number="7" size="254">
<constant cols="16" name="boostRefDCTable" rows="14" units="Boost control DC">
10.2 10.2 20.0 20.0 30.2 30.2 30.2 30.2 30.2 80.4 80.4 80.0 80.0 80.0 80.0 60.0
10.2 10.2 30.2 30.2 30.2 30.2 30.2 40.0 50.2 80.4 80.4 80.4 80.4 70.2 70.2 70.2
10.2 10.2 50.2 50.2 50.2 50.2 50.2 60.0 60.0 80.0 80.4 80.4 80.4 80.4 70.2 80.0
60.0 60.0 50.2 50.2 50.2 50.2 50.2 60.0 60.0 60.0 80.0 80.4 80.4 80.4 80.0 90.2
60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 70.2 70.2 80.4 80.4 80.4 80.4 80.0 90.2
60.0 60.0 70.2 60.0 60.0 60.0 60.0 70.2 80.0 80.0 80.0 80.0 80.0 80.0 80.0 90.2
60.0 70.2 80.0 70.2 70.2 70.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 80.0
60.0 70.2 80.0 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 90.2 80.0 80.0 80.0
60.0 70.2 80.0 85.1 85.1 80.0 80.4 80.4 80.0 80.0 80.0 80.0 80.0 80.0 80.0 80.0
60.0 70.2 85.1 85.1 85.1 85.1 65.1 65.5 65.5 80.4 80.4 80.4 80.0 80.0 80.0 80.0
60.0 90.2 90.2 90.2 90.2 90.2 60.0 56.1 57.2 58.0 70.2 75.3 75.3 74.9 74.9 74.9
60.0 90.2 90.2 90.2 90.2 90.2 60.0 56.1 55.3 54.9 67.8 70.2 70.2 70.2 70.2 70.2
90.2 90.2 90.2 94.9 94.9 90.2 60.0 50.6 50.6 55.3 65.1 70.2 70.2 70.2 70.2 70.2
90.2 90.2 90.2 90.2 90.2 90.2 80.0 50.6 50.2 50.2 50.2 50.2 50.2 50.2 50.2 50.2
</constant>
<constant name="boostRefDCTableO" rows="16" units="Boost control DC">
10.2
10.2
20.0
20.0
30.2
30.2
30.2
30.2
30.2
80.4
80.4
80.0
80.0
80.0
80.0
60.0
</constant>
<constant name="mapBinsB" rows="14" units="kPa">
30
46
56
60
70
80
96
110
136
180
230
290
350
400
</constant>
<constant name="rpmBinsB" rows="16" units="RPM">
700
1100
1400
1700
2200
2600
3000
3500
4000
4600
5100
5500
6000
6400
6900
7400
</constant>
</page>
<page number="8" size="110">
<constant name="acc_coeff_cold" units="%">77</constant>
<constant name="acc_coeff_warm" units="%">100</constant>
<constant name="acc_fadeout_rate1" units="%">39</constant>
<constant name="acc_fadeout_rate2" units="%">50</constant>
<constant name="acc_tps_deadband" units="%">39</constant>
<constant name="boost_1" units="%">0</constant>
<constant name="boost_2" units="%">0</constant>
<constant name="boost_3" units="%">0</constant>
<constant name="boost_4" units="%">0</constant>
<constant name="boost_5" units="%">0</constant>
<constant name="boost_tps_dc_scale" units="%">78</constant>
<constant name="boostgauge_channel">0</constant>
<constant name="boostgauge_channel_bits">"7"</constant>
<constant name="boostgauge_channel_enable">"Disabled"</constant>
<constant name="boostgauge_channel_names">"Disabled"</constant>
<constant name="boostgauge_mul">0</constant>
<constant name="boostgauge_offset">0</constant>
<constant name="boostsw_channel">"0"</constant>
<constant name="boostsw_conf">0</constant>
<constant name="boostsw_enable">"Disabled"</constant>
<constant name="dec_coeff_cold" units="%">100</constant>
<constant name="dec_coeff_warm" units="%">77</constant>
<constant name="dec_fadeout_rate1" units="%">50</constant>
<constant name="dec_fadeout_rate2" units="%">39</constant>
<constant name="dec_tps_deadband" units="%">50</constant>
<constant name="film_coeff_cold" units="%">73</constant>
<constant name="film_coeff_warm" units="%">100</constant>
<constant name="film_rate">95</constant>
<constant name="film_rpm_scale" units="%">38</constant>
<constant name="film_scale">128</constant>
<constant name="gear_1" units="kph">0</constant>
<constant name="gear_2" units="kph">0</constant>
<constant name="gear_3" units="kph">0</constant>
<constant name="gear_4" units="kph">0</constant>
<constant name="gear_5" units="kph">0</constant>
<constant name="gear_6" units="kph">0</constant>
<constant name="iac_conf2">92</constant>
<constant name="iac_conf2_stepper_polarity">"Positive"</constant>
<constant name="inj_add_trim_0" units="us">0</constant>
<constant name="inj_add_trim_1" units="us">0</constant>
<constant name="inj_add_trim_2" units="us">0</constant>
<constant name="inj_add_trim_3" units="us">0</constant>
<constant name="inj_add_trim_4" units="us">0</constant>
<constant name="inj_add_trim_5" units="us">0</constant>
<constant name="inj_add_trim_6" units="us">0</constant>
<constant name="inj_add_trim_7" units="us">0</constant>
<constant name="inj_deadtime_10V" units="us">2048</constant>
<constant name="inj_deadtime_11V" units="us">2048</constant>
<constant name="inj_deadtime_12V" units="us">2048</constant>
<constant name="inj_deadtime_13V" units="us">2048</constant>
<constant name="inj_deadtime_14V" units="us">2048</constant>
<constant name="inj_deadtime_15V" units="us">2048</constant>
<constant name="inj_deadtime_6V" units="us">2048</constant>
<constant name="inj_deadtime_7V" units="us">2048</constant>
<constant name="inj_deadtime_8V" units="us">2048</constant>
<constant name="inj_deadtime_9V" units="us">2048</constant>
<constant name="inj_mult_trim_0" units="%">100.0</constant>
<constant name="inj_mult_trim_1" units="%">100.0</constant>
<constant name="inj_mult_trim_2" units="%">100.0</constant>
<constant name="inj_mult_trim_3" units="%">100.0</constant>
<constant name="inj_mult_trim_4" units="%">100.0</constant>
<constant name="inj_mult_trim_5" units="%">100.0</constant>
<constant name="inj_mult_trim_6" units="%">100.0</constant>
<constant name="inj_mult_trim_7" units="%">100.0</constant>
<constant name="injection_angle" units="deg">384</constant>
<constant name="knock_calibration_max">128</constant>
<constant name="knock_calibration_min">99</constant>
<constant name="knock_gain" rows="8" units="gain">
90
128
96
128
93
128
95
128
</constant>
<constant name="knock_gain0">"0.586"</constant>
<constant name="knock_gain1">"2"</constant>
<constant name="knock_gain2">"0.421"</constant>
<constant name="knock_gain3">"2"</constant>
<constant name="knock_gain4">"0.5"</constant>
<constant name="knock_gain5">"2"</constant>
<constant name="knock_gain6">"0.444"</constant>
<constant name="knock_gain7">"2"</constant>
<constant name="knock_reference" rows="8" units="ref">
97
128
93
128
96
128
99
128
</constant>
<constant name="knock_reference0">97</constant>
<constant name="knock_reference1">128</constant>
<constant name="knock_reference2">93</constant>
<constant name="knock_reference3">128</constant>
<constant name="knock_reference4">96</constant>
<constant name="knock_reference5">128</constant>
<constant name="knock_reference6">99</constant>
<constant name="knock_reference7">128</constant>
<constant name="launch_channel">15</constant>
<constant name="launch_channel_bits">"0"</constant>
<constant name="launch_channel_enable">"Disabled"</constant>
<constant name="launch_channel_names">"Disabled"</constant>
<constant name="launch_out_conf">97</constant>
<constant name="launch_out_conf_enable">"Disabled"</constant>
<constant name="launch_out_conf_offstate">"PWM low"</constant>
<constant name="launch_out_conf_pwmramp">"Enabled"</constant>
<constant name="launch_out_conf_speed">"48mS(Default)"</constant>
<constant name="launch_out_delay" units="s">0.0</constant>
<constant name="launch_out_ontime" units="s">0.0</constant>
<constant name="launch_out_pwmhigh" units="%">0</constant>
<constant name="launch_out_pwmlow" units="%">0</constant>
<constant name="launch_out_pwmramp" units="s">0.0</constant>
<constant name="map_filter_samples">"10"</constant>
<constant name="map_filter_triggers">"2"</constant>
<constant name="misc1out_condition1_clt" units="Â°C">31</constant>
<constant name="misc1out_condition1_egt" units="Â°C">1024</constant>
<constant name="misc1out_condition1_fac">">=CLT"</constant>
<constant name="misc1out_condition2_clt" units="Â°C">15</constant>
<constant name="misc1out_condition2_egt" units="Â°C">792</constant>
<constant name="misc1out_condition2_fac">"<=EGT"</constant>
<constant name="misc2out_condition1_clt" units="Â°C">14</constant>
<constant name="misc2out_condition1_egt" units="Â°C">776</constant>
<constant name="misc2out_condition1_fac">"Disabled"</constant>
<constant name="misc2out_condition2_clt" units="Â°C">31</constant>
<constant name="misc2out_condition2_egt" units="Â°C">1024</constant>
<constant name="misc2out_condition2_fac">"Disabled"</constant>
<constant name="n2o_channel">15</constant>
<constant name="n2o_channel_bits">"0"</constant>
<constant name="n2o_channel_enable">"Disabled"</constant>
<constant name="n2o_channel_names">"Disabled"</constant>
<constant name="n2o_enable">"Disabled"</constant>
<constant name="n2o_input">0</constant>
<constant name="n2o_launch_deactivation">"Disabled"</constant>
<constant name="n2o_maxkpa" units="kPa">0</constant>
<constant name="n2o_maxrpm" units="rpm">0</constant>
<constant name="n2o_mingear">1</constant>
<constant name="n2o_minkpa" units="kPa">0</constant>
<constant name="n2o_minrpm" units="rpm">0</constant>
<constant name="n2o_mintps" units="%">0</constant>
<constant name="n2o_retard" units="deg">0.0</constant>
<constant name="n2o_settings">3</constant>
<constant name="speed_sensor" units="Hz/100kph">0</constant>
<constant name="warning_above">"Less"</constant>
<constant name="warning_adc_channel">"0"</constant>
<constant name="warning_adc_value" units="Volt">1.86</constant>
<constant name="warning_afr" units="afr">9.6</constant>
<constant name="warning_channel">111</constant>
<constant name="warning_channel_bits">"6"</constant>
<constant name="warning_channel_enable">"Disabled"</constant>
<constant name="warning_channel_names">"Disabled"</constant>
<constant name="warning_clt" units="Â°C">31</constant>
<constant name="warning_egt" units="Â°C">952</constant>
<constant name="warning_knock">"Disabled"</constant>
<constant name="warning_kpa" units="kPa">192</constant>
<constant name="warning_rpm" units="rpm">12800</constant>
<constant name="warning_skip_time">"0.5s"</constant>
</page>
</msq>

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: GintsK on March 03, 2009, 12:12:15 AM

Ouch! :o
May be you can find a way save your .msq on public server and give us only link. e.g. rapidshare.com
I tried put together your pieces. No success...

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on March 03, 2009, 12:20:09 AM

Okay - email me the msq file and I will put it on the server so it can be downloaded.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on March 03, 2009, 04:36:12 AM

Here it is:

http://www.vems.co.uk/VEMSConfigs/test60-2X.msq

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: GintsK on March 04, 2009, 01:05:27 AM

Now it opens.
I see some misconfiguration in secondary trigger:
angular width of tooth lower byte must be 6deg*4=24 (0.25deg step)
angular width of tooth upper byte must be 0 (http://www.vems.hu/wiki/index.php?page=GenBoard%2FUnderDevelopment%2FFirmwareChanges read notes on 1.1.30 and 1.1.32)
Engine phase to reset 64 [720deg*4=2880 (in 0.25degries) ; 2880/256=11.25 (8bit counter); 0.25*256=64 (raw counter value at reset)] ;)

It is good idea to upgrade firmware to something newer - these settings now are much more straightforward and user friendly.
Recheck your advance after changes, please!

Gints

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 04, 2009, 03:34:24 AM

Hello GintsK

Thank you for this very good Tip :D

The engine is runing without problems over 4000 rpm

IÂ´m working 2 weeks with this problem, but my problem is that my english is very bad and I understand many Details from vems wiki not.

Thank you and good time

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on March 04, 2009, 03:55:11 AM

Those of us with good English cannot understand the wiki.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 04, 2009, 10:34:45 AM

Hello Rob

thats right what you say.

with bad english is this problem bigger, the translate programs for technical english is all shit.

ThankÂ´s for the help at this Community Forum

@GintsK All what you say was rihgt i have only change this value and the engine was running perfect Thanks again.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on March 04, 2009, 03:32:37 PM

Quote from: Regler on March 04, 2009, 10:34:45 AM
with bad english is this problem bigger, the translate programs for technical english is all shit.

Much of the wiki is written by people who have english as their second language, although their english is very good (better than any second language that I have) it does lead to confusion sometimes.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: GintsK on March 04, 2009, 10:30:33 PM

Regler, remember recheck advance. And also you need to fill MAT table. Otherwise you leaves without any correction from air temperature.

English in some wiki pages together with abbreviations from config.txt and coders slang are some kind of brain workout. I can't understand these sentences for hours and days either! But sometimes I am a winner: light comes up and expose the real matter of authors ideas. ;D Not an easy reading!

English is not my second language. It's third after Russian. May be that is a problem...

Gints

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 07, 2009, 02:21:54 AM

Hello GintsK

Yes its right i must make the Mat correction.

i was today with this car and Vems ecu on Dynometer the result is very good :)

670HP and 900 NM Torque at 3900 rpm have the car 600 Nm and at 5000 rpm 900 NM Torque with 2,5L 5 cylinder Turbo

Have you experience with Antilag and Launch Control with Megatune?

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 07, 2009, 02:52:02 AM

How can to fit a picture in a post, or Rob can I send the Dyno Picture to you at email?

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: GintsK on March 07, 2009, 02:01:11 PM

Wow 900Nm! What engine internals you use! What turbo? I suppose boost is about 3bar?

Last season I was problems with launch control. I can not adjust it for stable boost on strat line. On low retarding it rises too slowly, with high retard boost goes up to regulated by W-gate boost. And it was too much. You can find description of problem in my wiki and here also.

My idea for new season is use switchable config, when launch is active. It allow to set another boost level desired at start line.

In newer firmwares shift cut is improved - not 100% cut and retarded ignition. It can be used to keep boost during shifting. Last year was no chance.
I have no experience with ALS.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: gunni on March 07, 2009, 02:56:03 PM

Quote from: Regler on March 07, 2009, 02:52:02 AM
How can to fit a picture in a post, or Rob can I send the Dyno Picture to you at email?

and post your engine specs as well

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 08, 2009, 03:40:52 AM

Hello gunni,

the engine is a 2,5l 5 cylinder 20V Turbo with GT35 Turbocharger mechnic valve mahle race pistons specific exhaust manifold and and.....

if rob gives OK I send the pictures

@gintsK

The pressure for 900NM are 2,8 bar (with atmosphÃ¤re 3,8 bar) and at max power is the pressure 2,3 bar

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: gunni on March 08, 2009, 06:12:18 AM

Any changes to the head, camshaft, valvetrain?

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on March 08, 2009, 03:05:29 PM

Quote from: Regler on March 08, 2009, 03:40:52 AM
if rob gives OK I send the pictures

Sure, send them over.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on March 09, 2009, 01:43:06 AM

(http://www.vems.co.uk/UserContributions/2,5L%20Turbo.jpg)
(http://www.vems.co.uk/UserContributions/DSC00980.JPG)
(http://www.vems.co.uk/UserContributions/DSC00982.JPG)
(http://www.vems.co.uk/UserContributions/DSC00985.JPG)
(http://www.vems.co.uk/UserContributions/DSC00986.JPG)
(http://www.vems.co.uk/UserContributions/DSC00988.JPG)
(http://www.vems.co.uk/UserContributions/DSC00993.JPG)
(http://www.vems.co.uk/UserContributions/DSC01002.JPG)
(http://www.vems.co.uk/UserContributions/DSC01004.JPG)
(http://www.vems.co.uk/UserContributions/DSC01012.JPG)
(http://www.vems.co.uk/UserContributions/DSC01013.JPG)
(http://www.vems.co.uk/UserContributions/DSC01014.JPG)
(http://www.vems.co.uk/UserContributions/DSC01015.JPG)
(http://www.vems.co.uk/UserContributions/DSC01016.JPG)
(http://www.vems.co.uk/UserContributions/DSC01018.JPG)
(http://www.vems.co.uk/UserContributions/DSC01019.JPG)
(http://www.vems.co.uk/UserContributions/DSC01034.JPG)
(http://www.vems.co.uk/UserContributions/DSC01036.JPG)
(http://www.vems.co.uk/UserContributions/DSC01037.JPG)
(http://www.vems.co.uk/UserContributions/DSC01040.JPG)
(http://www.vems.co.uk/UserContributions/DSC01046.JPG)

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on March 12, 2009, 02:50:20 AM

Hello,

I have a new question

how can I conect a warning beep light on the vems audi motronic

The vems have a 6pin AMP Conector what outpout can I take?

In the settings from experimental I would take the exhaust temp over 950Â°C and the the light go on

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Jeffer on March 31, 2009, 03:56:50 PM

Looks nice.
Can I ask some questions?
What turbo do you run?
Wich cams?
Thanks,
Jeffer

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Regler on April 05, 2009, 09:22:20 PM

Hello Jeffer,

the turbo is a gt3582
the mechanic cams are 227Â° and 10,55 mm lift

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: audis2turbo on April 18, 2009, 03:39:12 PM

Quote from: Regler on April 05, 2009, 09:22:20 PM
Hello Jeffer,

the turbo is a gt3582
the mechanic cams are 227Â° and 10,55 mm lift

Hello Regler,
you are from Germany?
I use the same cam`s from PK with a Turbonetics GT-K550.
Have you any Pictures from the Clutch with the 60tooth Wheel???
Greets AudiS2Turbo

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Jamo on April 25, 2012, 10:11:12 AM

Whats happened to the pics? they were there a week or two ago I wanted to see them

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: [email protected] on April 25, 2012, 11:28:03 AM

I'm in the process of handing over the vems.co.uk domain to the owners of VEMS. If you send me your email I'll zip them up and send them over.
The vems.co.uk site is down too and no emails are coming through.

Title: Re: Audi 20V Turbo 5 Cylinder
Post by: Jamo on April 25, 2012, 05:39:14 PM

They are back up now :)

VEMS Community Forum

Members => Projects & Installs => Topic started by: Regler on February 28, 2009, 02:47:29 AM