VEMS Community Forum
Technical => Triggering => Topic started by: derill3237 on July 23, 2020, 07:39:31 pm
-
Help solve the problem ..
I connected a wems on the table (firmware 1.2.11).
Connected CAS ca18det ..
The trigger does not display a signal from the camshaft sensor ...
Attached config and triggerlog ..
http://wdfiles.ru/jenE
http://wdfiles.ru/f2f7
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
-
Board set for hall trigger?
-
Board set for hall trigger?
Yes
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
SJ 2 closed
Primary trigger hall
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
SJ 2 closed
Primary trigger hall
and pullup resistor not changed :))
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
SJ 2 closed
Primary trigger hall
and pullup resistor not changed :))
R30 4.7kOm
if I choose 36-1 camsync in the settings ..
signals from the crankshaft and camshaft sensor are visible in the log.
and when I choose nissan ...
does not see the camshaft sensor ..
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
SJ 2 closed
Primary trigger hall
and pullup resistor not changed :))
R30 4.7kOm
if I choose 36-1 camsync in the settings ..
signals from the crankshaft and camshaft sensor are visible in the log.
and when I choose nissan ...
does not see the camshaft sensor ..
did you know that one with small amount of slots goes to primary trigger and 360 one goes to sec trigger, and then when you select nissan trigger yes you wont see secondary trigger as I remember + if you want to see it you need to put ecu in safe mode
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
SJ 2 closed
Primary trigger hall
and pullup resistor not changed :))
R30 4.7kOm
if I choose 36-1 camsync in the settings ..
signals from the crankshaft and camshaft sensor are visible in the log.
and when I choose nissan ...
does not see the camshaft sensor ..
read this
http://vems.hu/vt/help/v3/v3_secondary_trigger_settings.html
http://www.vems.hu/wiki/index.php?page=InputTrigger%2FNissanTrigger
-
Are you able to measure the signal output of the CAS via a scope or at least a multimeter?
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V
it looks that primary trigger in your ecu is vr not hall
SJ 2 closed
Primary trigger hall
and pullup resistor not changed :))
R30 4.7kOm
if I choose 36-1 camsync in the settings ..
signals from the crankshaft and camshaft sensor are visible in the log.
and when I choose nissan ...
does not see the camshaft sensor ..
did you know that one with small amount of slots goes to primary trigger and 360 one goes to sec trigger, and then when you select nissan trigger yes you wont see secondary trigger as I remember + if you want to see it you need to put ecu in safe mode
Thank ..
I probably understood what my mistake was ..