Recent Posts

Pages: 1 [2] 3 4 ... 10
11
Wideband & EGT Gauge / Display round
« Last post by james on May 08, 2022, 08:07:58 pm »
Hi all, if I connect a display round to my ecu is it still possible to have the bluetooth transmitter connected to connect my laptop at the same time?

Thanks

James
12
Software / Re: Firmware 1.2.44 ?
« Last post by 299vr6-t on May 05, 2022, 10:47:10 pm »
Hi ,


Are there some updates planned for future ?

Greetings from germany
13
Triggering / Re: Loss of prime trigger on FW 1.2.43
« Last post by jrussell on April 28, 2022, 02:22:29 pm »
So don't use those firmwares? They are not released anyway. 1.2.38 is recommended.

Read the notes on the versions since 1.2.38 here: http://www.vems.hu/wiki/index.php?page=GenBoard%2FUnderDevelopment%2FFirmwareChanges

They all say experimental, do not use yet.

1.2.43 had some specific trigger related changes for a Subaru EJ255 and hasn't been thoroughly tested or released yet. Not really a surprise it didn't run a VR6 or AAN.
14
Software / Re: Firmware 1.2.44 ?
« Last post by jrussell on April 28, 2022, 02:15:34 pm »
You should never be trying new firmware unless it's on this page as released http://www.vems.hu/wiki/index.php?page=GenBoard%2FUnderDevelopment%2FFirmwareChanges or someone from VEMS Support (or your tuner) tells you to use a different specific version for a specific reason.
15
Software / Firmware 1.2.44 ?
« Last post by 299vr6-t on April 25, 2022, 12:42:00 pm »
Hello

has anybody some infos about Firmware 1.2.44 ?
It´s shown in FW Webupdate tool.
I tried it, but for me it doesnt work because i get lots of trigger errors. So i must went back to 1.2.38

 :-\
16
Triggering / Re: Loss of prime trigger on FW 1.2.43
« Last post by 299vr6-t on April 25, 2022, 12:38:55 pm »
Today tried FW 1.2.44
Same issue, "to many prim. trigger".

It´s not good that there is any support for those special things.

 :(
17
Does anyone have some recommended settings to get the knock sensors working? Whenever I get the average knock value close to my knock reference average setup correctly and turn on knock detection it constantly goes off. (isknocking always on). I tried to play with the threshold for mean value with no luck.
base settings from menus are quite good :))
18
General Discussion / Re: UK tuning
« Last post by Kamuto on April 08, 2022, 12:27:53 pm »
hello there,

Good luck, they are like gold dust in the UK, i think the best you can do, is look for someone with at least megasquirt knowledge.

I would love to get my car fully sorted, as I've done my best with it, but its not 100%....but hey i can drive it....lol....before the government ban us of the road.

Good luck, and let me know if you find a miracle hiding somewhere.

regards
scott
I trawel there from time to time :))
19
Does anyone have some recommended settings to get the knock sensors working? Whenever I get the average knock value close to my knock reference average setup correctly and turn on knock detection it constantly goes off. (isknocking always on). I tried to play with the threshold for mean value with no luck.
20
Wiring & Sensors / Re: Motronic55 to BMW e30 with m20b25
« Last post by macintosh14568 on March 31, 2022, 07:37:50 pm »
https://www.pnpecu.com/ makes a pnp setup for this. Although you may need to switch some wires around in your x20 connector to get body related stuff working.
Pages: 1 [2] 3 4 ... 10