Author Topic: Mini MPi sectrig problem  (Read 2762 times)

Offline FullGasCZ

  • Jr. Member
  • **
  • Posts: 7
  • BHP: 0
Mini MPi sectrig problem
« on: December 20, 2021, 09:55:20 pm »
Hi, i have problem with sectric on Mini Mpi, it is stock VR sensor and ecu dont accept this signal. It should be that voltage on the peak is too low? Or shape of curve is incorrect? The sensor is in the groove in the lobe of camshaft.

Thank You for answer


Offline FullGasCZ

  • Jr. Member
  • **
  • Posts: 7
  • BHP: 0
Re: Mini MPi sectrig problem
« Reply #1 on: December 20, 2021, 10:01:41 pm »

Offline Kamuto

  • Hero Member
  • *****
  • Posts: 814
  • BHP: 19
Re: Mini MPi sectrig problem
« Reply #2 on: December 21, 2021, 11:05:15 pm »
Hi, i have problem with sectric on Mini Mpi, it is stock VR sensor and ecu dont accept this signal. It should be that voltage on the peak is too low? Or shape of curve is incorrect? The sensor is in the groove in the lobe of camshaft.

Thank You for answer


maybe your ecu is configured with hall trigger hw for secondary trigger?
Vems installer in Lithuania
[email protected]

Offline FullGasCZ

  • Jr. Member
  • **
  • Posts: 7
  • BHP: 0
Re: Mini MPi sectrig problem
« Reply #3 on: December 22, 2021, 07:34:49 pm »
Hi, i have problem with sectric on Mini Mpi, it is stock VR sensor and ecu dont accept this signal. It should be that voltage on the peak is too low? Or shape of curve is incorrect? The sensor is in the groove in the lobe of camshaft.

Thank You for answer

maybe your ecu is configured with hall trigger hw for secondary trigger?
No, ecu is configured correct. Or can i verify it somehow?

photo: https://ibb.co/M7WDYy2

« Last Edit: December 22, 2021, 07:36:36 pm by FullGasCZ »

Offline Kamuto

  • Hero Member
  • *****
  • Posts: 814
  • BHP: 19
Re: Mini MPi sectrig problem
« Reply #4 on: December 30, 2021, 06:42:10 am »
Hi, i have problem with sectric on Mini Mpi, it is stock VR sensor and ecu dont accept this signal. It should be that voltage on the peak is too low? Or shape of curve is incorrect? The sensor is in the groove in the lobe of camshaft.

Thank You for answer

maybe your ecu is configured with hall trigger hw for secondary trigger?
No, ecu is configured correct. Or can i verify it somehow?

photo: https://ibb.co/M7WDYy2
on your paper it writes sec trigger hall, and you are using VR sensor for that, so that's your answer..
Vems installer in Lithuania
[email protected]

Offline FullGasCZ

  • Jr. Member
  • **
  • Posts: 7
  • BHP: 0
Re: Mini MPi sectrig problem
« Reply #5 on: January 04, 2022, 07:42:51 am »
Hi, i have problem with sectric on Mini Mpi, it is stock VR sensor and ecu dont accept this signal. It should be that voltage on the peak is too low? Or shape of curve is incorrect? The sensor is in the groove in the lobe of camshaft.

Thank You for answer

maybe your ecu is configured with hall trigger hw for secondary trigger?
No, ecu is configured correct. Or can i verify it somehow?

photo: https://ibb.co/M7WDYy2
on your paper it writes sec trigger hall, and you are using VR sensor for that, so that's your answer..
Really? i see Sec trig VR, where is the problem?

Offline Kamuto

  • Hero Member
  • *****
  • Posts: 814
  • BHP: 19
Re: Mini MPi sectrig problem
« Reply #6 on: January 11, 2022, 06:41:28 am »
Hi, i have problem with sectric on Mini Mpi, it is stock VR sensor and ecu dont accept this signal. It should be that voltage on the peak is too low? Or shape of curve is incorrect? The sensor is in the groove in the lobe of camshaft.

Thank You for answer

maybe your ecu is configured with hall trigger hw for secondary trigger?
No, ecu is configured correct. Or can i verify it somehow?

photo: https://ibb.co/M7WDYy2
on your paper it writes sec trigger hall, and you are using VR sensor for that, so that's your answer..
Really? i see Sec trig VR, where is the problem?
you are right.. my bad
Vems installer in Lithuania
[email protected]