Author Topic: i need a firmware version!  (Read 5692 times)

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
i need a firmware version!
« on: April 22, 2014, 08:12:47 pm »
Hi

i´m currently working on a avcs subaru setup and i have before used this setup with firmware 1.2.11 and i have been working,
but now i cant change the cam ref tooth ,
just like i have descibed here :

http://www.vems.hu/wiki/index.php?page=SubaruEj

The avcs control does not work like its surposed to, the sectric and thirdtric is showing around 167degrees when at idle
• it should be lowered to 20-30 crankdeg with "measure at toothcnt" but it can not be lowered with "measure at toothcount"
• can you show related config(s) and preferrably triggerlog also so it can be reproduced ?

Note: config.strig_validation bits

//See global.h... bit 0,1 camshaft measure count for Subaru and Suzuki VVTI
1.define CAMSHAFT_MEASURE_PULSE_CNT_MASK ( _BV(0) + _BV(1) )
• yes tooth 2,5,8 or 11 can be selected
• so the 36-2-2-2 subaru triggercode had traditionally 2 configbits (bottom of config.strig_validation) for setting the "measure tooth at". Back in those days the separate "sectrig measure tooth" and "thirdtrig measure tooth" did not exist (and config was not changed to not cause upgrade problem)
• from fw 1.2.13 (2013-05-13) the "measure tooth at" values are used (and config.strig_validation bit0-1 neglected for subaru and suzuki 36-2-2-2) the same config bytes similarly as for other triggertypes (0-15)
• so when i try to advance it to more then 180degrees it will show a measuretooth of 30-40degrees,this will result in the DutyCycle? to go to 100, and the engine will stall.





 and it says on the subaru trigger page that i need firmware 1.2.13 , but that can not be downloaded anywere ??

the firmware jump from 1.2.12 to 1.2.20 , and as this is a old pcb i cant use the newer firmware ,

Were can i download a working firmware ?


Thanks,
Skassa

working on the boxer

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: i need a firmware version!
« Reply #1 on: April 23, 2014, 06:28:07 am »
Anyone  ?

Were Can i download a firmware version between 1.2.11 and 1.2.19 ?

Thanks
Skassa
working on the boxer

Offline fphil

  • Sr. Member
  • ****
  • Posts: 398
  • BHP: 6
Re: i need a firmware version!
« Reply #2 on: April 23, 2014, 08:05:05 am »
1.2.19 is no more there : http://svn.x-dsl.hu/f/
I can mail it to you if you wish
Philippe

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: i need a firmware version!
« Reply #3 on: April 23, 2014, 08:13:34 am »
Yes a bit Strange that they have all been remowed , not good if you plan to run a subaru avcs engine and have a old ecu ,


Mail it : Yes that would be great :)


[email protected]


Thanks
Skassa
working on the boxer

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: i need a firmware version!
« Reply #4 on: April 23, 2014, 11:26:46 am »
I have found som firmware under a folder named DONT USE

http://svn.x-dsl.hu/f/DONTUSE/

i dont know if it a good ide to use one of those , but as i acording to the wiki side need 1.2.13 OR newer to control avcs then i must use one og the DONT USE firmware

Any suggestions to what to use ?

I just find it Strange that the 1.2.11 firmware that i have in my other ecu works and the 1.2.11 that i download with the firmware tool in vemstune dosent work ??


Thanks
Skassa
working on the boxer

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: i need a firmware version!
« Reply #5 on: April 23, 2014, 02:54:55 pm »
Also found this

Dont know what obsolete means ?


http://www.vems.hu/download/v3/firmware/obsolete/
working on the boxer

Offline Kamuto

  • Hero Member
  • *****
  • Posts: 814
  • BHP: 19
Re: i need a firmware version!
« Reply #6 on: April 23, 2014, 05:13:28 pm »
I'll be starting one 2005 sti crank vr sensor + 2 hall sensors on cams, it won't works too?
Vems installer in Lithuania
[email protected]

Offline fphil

  • Sr. Member
  • ****
  • Posts: 398
  • BHP: 6
Re: i need a firmware version!
« Reply #7 on: April 24, 2014, 09:18:19 am »
Yes a bit Strange that they have all been remowed , not good if you plan to run a subaru avcs engine and have a old ecu ,


Mail it : Yes that would be great :)


[email protected]


Thanks
Skassa

A message that you sent could not be delivered to one or more of its
recipients. This is a permanent error. The following address(es) failed:

  [email protected]
    mailbox is full: retry timeout exceeded

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: i need a firmware version!
« Reply #8 on: April 24, 2014, 04:08:22 pm »
Hmm
Thats Strange , i have just tried to send a mail and it works normally ,

But i did get the firmware downloades yesterday and it works :)


Thanks
Skassa
working on the boxer

Offline fphil

  • Sr. Member
  • ****
  • Posts: 398
  • BHP: 6
Re: i need a firmware version!
« Reply #9 on: April 24, 2014, 05:15:25 pm »
???