Author Topic: ETC Module  (Read 6592 times)

Offline wersch

  • Jr. Member
  • **
  • Posts: 60
  • BHP: 1
  • ECU installer in Sweden
ETC Module
« on: May 25, 2016, 10:09:30 pm »
Is there any more info available how to connect the etc module to vems on a ecu without prewired loom for this?
I have a v3.8 ecu that needs drive by wire.

Greetings Rickard

Offline PeepPaadam

  • Sr. Member
  • ****
  • Posts: 250
  • BHP: 8
Re: ETC Module
« Reply #1 on: May 28, 2016, 11:05:22 am »
The PWM output is the unused hole right next to MAP sensor holes. There is 7 holes in a row, 6 are used by MAP sensor, 7th is PWM output. Besides that, only GND is needed and that's all.

Offline MWfire

  • Hero Member
  • *****
  • Posts: 721
  • BHP: 35
Re: ETC Module
« Reply #2 on: May 30, 2016, 10:08:26 am »
Or use spare inj output.

Offline wersch

  • Jr. Member
  • **
  • Posts: 60
  • BHP: 1
  • ECU installer in Sweden
Re: ETC Module
« Reply #3 on: July 29, 2016, 10:17:34 pm »
Sorry for the late response, but now i have the ETC module on the table and can test it.
Are you saying i should connect the PWM output directly to pin 1 on the SSC6 connector (Bridge-control)?
No resistors or diodes or similar?
Pin 6 should it be connected to power GND?

And if i want to control PFET outputs 2,3,4,5 do i connect these to P259 outputs?

MWfire:
When you say use injector output, are you saying that i should connect the motor directly here?



Offline Bn74wrc

  • New Users
  • *
  • Posts: 1
  • BHP: 0
Re: ETC Module
« Reply #4 on: February 11, 2018, 07:09:10 am »
Hello, any update ?:)

Offline MWfire

  • Hero Member
  • *****
  • Posts: 721
  • BHP: 35
Re: ETC Module
« Reply #5 on: February 11, 2018, 09:29:32 am »


MWfire:
When you say use injector output, are you saying that i should connect the motor directly here?


No, you can connect H output for ETC on spare injector output.

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: ETC Module
« Reply #6 on: October 20, 2021, 11:44:28 am »
Can anyone explain this in a Way so ordenary people understand how to connect this module and set it up
 

This is a really bad diagram on how to connect it and get it working

working on the boxer

Offline Kamuto

  • Hero Member
  • *****
  • Posts: 811
  • BHP: 19
Re: ETC Module
« Reply #7 on: October 22, 2021, 11:09:42 pm »
Can anyone explain this in a Way so ordenary people understand how to connect this module and set it up
 

This is a really bad diagram on how to connect it and get it working

:D it's not for ordinary people, anyway I would help you if you wrote me on facebook
Vems installer in Lithuania
[email protected]

Offline jrussell

  • VEMS USA
  • Administrator
  • Full Member
  • *****
  • Posts: 215
  • BHP: 15
    • VEMS USA
Re: ETC Module
« Reply #8 on: October 27, 2021, 09:08:50 pm »
This isn't hard.

Either the pwm pad as Peep pointed out, or a spare injector output as Valdas pointed out goes to SSC6 pin 1 (Bridge control). SSC6 pin 6 (GND) needs to be connected as well, naturally.

Forget about the PFET, those aren't for ETC. Do that later if you need.

People should be ordering the ECU with ETC so you can just plug it in. Or order the ECU with the ETC mounted inside.
VEMS USA - Located in beautiful Burlington, Vermont
1988 RX7 Turbo