Technical > Triggering

Nissan Trigger Problems 16 12 8 4 (ca18det)

<< < (2/3) > >>

Kamuto:

--- Quote from: derill3237 on July 24, 2020, 07:15:22 pm ---
--- Quote from: gunni on July 24, 2020, 03:46:54 pm ---Are you able to measure the signal output of the CAS via a scope or at least a multimeter?

--- End quote ---
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V

--- End quote ---
it looks that primary trigger in your ecu is vr not hall

derill3237:

--- Quote from: Kamuto on July 25, 2020, 12:00:49 am ---
--- Quote from: derill3237 on July 24, 2020, 07:15:22 pm ---
--- Quote from: gunni on July 24, 2020, 03:46:54 pm ---Are you able to measure the signal output of the CAS via a scope or at least a multimeter?

--- End quote ---
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V

--- End quote ---
it looks that primary trigger in your ecu is vr not hall

--- End quote ---

SJ 2 closed
Primary trigger hall

Kamuto:

--- Quote from: derill3237 on July 25, 2020, 09:40:10 pm ---
--- Quote from: Kamuto on July 25, 2020, 12:00:49 am ---
--- Quote from: derill3237 on July 24, 2020, 07:15:22 pm ---
--- Quote from: gunni on July 24, 2020, 03:46:54 pm ---Are you able to measure the signal output of the CAS via a scope or at least a multimeter?

--- End quote ---
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V

--- End quote ---
it looks that primary trigger in your ecu is vr not hall

--- End quote ---

SJ 2 closed
Primary trigger hall

--- End quote ---

and pullup resistor not changed :))

derill3237:

--- Quote from: Kamuto on July 26, 2020, 12:06:56 pm ---
--- Quote from: derill3237 on July 25, 2020, 09:40:10 pm ---
--- Quote from: Kamuto on July 25, 2020, 12:00:49 am ---
--- Quote from: derill3237 on July 24, 2020, 07:15:22 pm ---
--- Quote from: gunni on July 24, 2020, 03:46:54 pm ---Are you able to measure the signal output of the CAS via a scope or at least a multimeter?

--- End quote ---
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V

--- End quote ---
it looks that primary trigger in your ecu is vr not hall

--- End quote ---

SJ 2 closed
Primary trigger hall

--- End quote ---

and pullup resistor not changed :))

--- End quote ---

R30 4.7kOm

if I choose 36-1 camsync in the settings ..
signals from the crankshaft and camshaft sensor are visible in the log.
and when I choose nissan ...
does not see the camshaft sensor ..

Kamuto:

--- Quote from: derill3237 on July 26, 2020, 10:36:23 pm ---
--- Quote from: Kamuto on July 26, 2020, 12:06:56 pm ---
--- Quote from: derill3237 on July 25, 2020, 09:40:10 pm ---
--- Quote from: Kamuto on July 25, 2020, 12:00:49 am ---
--- Quote from: derill3237 on July 24, 2020, 07:15:22 pm ---
--- Quote from: gunni on July 24, 2020, 03:46:54 pm ---Are you able to measure the signal output of the CAS via a scope or at least a multimeter?

--- End quote ---
Secondery trigger 4.52 - 0.09V
Primary trigger 2.05 - 0.05V

--- End quote ---
it looks that primary trigger in your ecu is vr not hall

--- End quote ---

SJ 2 closed
Primary trigger hall

--- End quote ---

and pullup resistor not changed :))

--- End quote ---

R30 4.7kOm

if I choose 36-1 camsync in the settings ..
signals from the crankshaft and camshaft sensor are visible in the log.
and when I choose nissan ...
does not see the camshaft sensor ..

--- End quote ---

did you know that one with small amount of slots goes to primary trigger and 360 one goes to sec trigger, and then when you select nissan trigger yes you wont see secondary trigger as I remember + if you want to see it you need to put ecu in safe mode

Navigation

[0] Message Index

[#] Next page

[*] Previous page