Author Topic: Suzuki sj410 with gti swift 1.3 dohc engine  (Read 12905 times)

Offline Rak

  • Jr. Member
  • **
  • Posts: 24
  • BHP: 0
Suzuki sj410 with gti swift 1.3 dohc engine
« on: November 01, 2015, 06:39:54 pm »
First of all, sorry for my english  ;D

So, this project started in 2006, leading installation of gti engine and vems v3.3 on 2008. Since then i've been mostly driving around, replacing cv-joints and some minor fixes :)
Original building topic, in finnish:
http://offroadoulu.com.www32.zoner-asiakas.fi/smf_forum/index.php?topic=758.0


V3.3_n001652 Fw1.2.11 (cant update newer, because uhex and so on ;) )
Map and iat sensor: http://www.amazon.co.uk/Bosch-0281002437-Pressure-Temperature-Sensor-x/dp/B00279MT9M
Wideband o2, lsu 4.2 i think
Egt
Clt sensor from siemens
Original low-z(2ohm) injectors with 6ohm resistors
Original swift tps
Original fpr
Fuel pump from random Opel
Crank sensor is reading holes from flywheel, 36-1


Vems controls cooling fan

Other pics from current installation:





V3.3 1652
FW 1.2.38

Offline Rak

  • Jr. Member
  • **
  • Posts: 24
  • BHP: 0
Re: Suzuki sj410 with gti swift 1.3 dohc engine
« Reply #1 on: November 01, 2015, 07:05:35 pm »
And now we can go to the reason why i am here now:)

Month ago tip of cyl.3 valveguide broke of and fell in to the cylinder.



I replaced cylinderhead, updated firmware from 1.0.73( or something like that) to 1.2.11.
New cylinderhead is ported, camshafts and timing are stock.

Problem is poor idle, it misfires and runs "heavy",   old engine didn't have this problem.
Voice sample:
https://www.youtube.com/watch?v=P9OcaY0wAeM&feature=youtu.be

Compressions are "quite" good:


Edit: Changing injectors, coil, sparkplugs and wires didnt make any difference. Ignition timing checked with lamp. Fuel pressure also ok.
Injector, ignition and cranksensor signals checked with oscilloscope. There were no interference as far as i can tell.

I have a little bit of log and config of course. Trying to find a place to upload those.
« Last Edit: November 02, 2015, 06:10:51 pm by Rak »
V3.3 1652
FW 1.2.38

Offline mattias

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1075
  • BHP: 41
    • Sävar Turbo Site
Re: Suzuki sj410 with gti swift 1.3 dohc engine
« Reply #2 on: November 01, 2015, 11:54:49 pm »

Offline Rak

  • Jr. Member
  • **
  • Posts: 24
  • BHP: 0
Re: Suzuki sj410 with gti swift 1.3 dohc engine
« Reply #3 on: November 02, 2015, 05:25:17 pm »
The server is not responding.. Am i missing something?
« Last Edit: November 02, 2015, 06:11:26 pm by Rak »
V3.3 1652
FW 1.2.38


Offline Rak

  • Jr. Member
  • **
  • Posts: 24
  • BHP: 0
Re: Suzuki sj410 with gti swift 1.3 dohc engine
« Reply #5 on: November 02, 2015, 06:34:42 pm »
Almost forgot.

I got 2 fuelpumps, 1 that pumps fuel from tank to a surge tank, and second that makes the pressure for injectors. Both have different relay, both relays are driven from ec36 pin 15 (p259, channel 5)

There was strange phenomenon when i was removing old engine, some point when i was loosening connectors and grounding from engine, low pressure pump activated. When i noticed that, i removed battery.
I am telling this so one can consider possibility that ecm is partially fried.
« Last Edit: November 05, 2015, 08:54:13 pm by Rak »
V3.3 1652
FW 1.2.38

Offline Rak

  • Jr. Member
  • **
  • Posts: 24
  • BHP: 0
Re: Suzuki sj410 with gti swift 1.3 dohc engine
« Reply #6 on: November 05, 2015, 09:07:44 pm »
Anyone?

On the road everything is fine, runs as it used to.

I've undergone base setup, but i dont find any obvious flaw.

V3.3 1652
FW 1.2.38

Offline Rak

  • Jr. Member
  • **
  • Posts: 24
  • BHP: 0
Re: Suzuki sj410 with gti swift 1.3 dohc engine
« Reply #7 on: March 07, 2018, 06:41:05 pm »
Found the problem, after changing engine.
I thought the camshafts were stock, they werent  :-[
Groung weirdly, 0.5mm more lift than stock, ~290 degree duration. No wonder it didnt idle.
Switched engine back in, now it runs good  :)
V3.3 1652
FW 1.2.38